Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup

Copy the “FlyPT_AeroflyFS2_UDP.dll” file included in the “Sources files” folder of the download, to the folder “...Documents\Aerofly FS 2\external_dll".

The DLL, broadcasts data to all IP's on port 4321, and it's not possible to change it for now.

Type

MMF - Game should run in same PC you have Mover running.

Setup

Not required.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup

Go to the options menu and use the values shown in the image.

You can change the ports, but they must match the ones used in Mover.

You can also change the update rate to get more data in Mover (depends on PC performance).

Acceleration smoothing can be achieved in Mover, but you can also adjust it in BeamNG.drive options.

Increase the update rate. By default, Mover works at 500hz, so move the "Update rate" slider to 500.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup

Go to the folder: "...\Condor2\Settings\"

Edit the file "UDP.ini" to match the following: 

In the IP, use:

• 127.0.0.1 if game runs in same PC of Mover.

• 255.255.255.255 to send data to all PC's on the network.

• The IP of the PC where Mover is running.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup

Get the script file “DCS to FlyPT Mover.lua” included inside the folder “Sources files” of the Mover download, and copy it to the folder “C:\Users\YOUR USERNAME\Saved Games\DCS\Scripts\Hooks”.

If the “Hooks” folder doesn't exist, create it.

Air and ground 

More info here.

Speed effect in drags

Drags are features that cause vibration, like flaps, stall or landing gear.

If speed is zero, there's no vibration, high speeds have more vibration.

Increasing this value, increases vibration for lower speeds.

Notes

Use wind value for fans, it takes into account how much of the canopy is open.

Troubleshooting

Make sure you put the  Lua file in the correct folder.

Make sure there's not another file Lua file using the same UDP port.

The Lua can be updated with new Mover updates. If it's not working, replace it with the new one.

Make sure you have permissions in the firewall. Try to disable it and see if it's working without firewall to discard this possibility. Same for antivirus software.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup for DiRT Rally:

Go to the folder “...Documents\My Games\DiRT Rally\hardwaresettings”.

Open for edit the file “hardware_settings_config.xml”.

Search for the string “<motion_platform>” and inside that section you will find a line similar to this one:

<udp enabled="true" extradata="2" ip="127.0.0.1" port="20777" delay="1" />

Ensure the selected values are the same pointed above, specially the “enabled” and “extradata”.

Setup for DiRT 3:

Go to the folder “...Documents\My Games\DiRT3\hardwaresettings”.

Open for edit the file “hardware_settings_config.xml”.

Search for the string "<motion enabled".

Modify the line to match the one bellow.

<motion enabled="true" ip="127.0.0.1" port="20777" delay="1" extradata="1" />

Setup for DiRT Showdown:

Go to the folder “...Documents\My Games\DiRT Showdown\hardwaresettings”.

Open for edit the file “hardware_settings_config.xml”.

Search for the string "<motion enabled".

Modify the line to match the one bellow.

<motion enabled="true" ip="127.0.0.1" port="20777" delay="1" extradata="1" />

Setup for GRID 2:  

Go to the folder “...Documents\My Games\GRID 2\hardwaresettings”.

Open for edit the file “hardware_settings_config.xml”.

Search for the string "<motion enabled".

Modify the line to match the one bellow.

<motion enabled="true" ip="127.0.0.1" port="20777" delay="1" extradata="2" />

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup for DiRT Rally 2:

Go to the folder “...Documents\My Games\DiRT Rally 2.0\hardwaresettings”.

Open for edit the file “hardware_settings_config.xml”.

Search for the string “<motion_platform>” and inside that section you will find a line similar to this one:

<udp enabled="true" extradata="3" ip="127.0.0.1" port="20777" delay="1" />

Ensure the selected values are the same pointed above, specially the “enabled” and “extradata”.

Important!

If you are using VR in DiRT 2, you need to edit the file "hardware_settings_config_vr.xml" in the same folder, with the same values.

Setup for DiRT 4:

Go to the folder “...Documents\My Games\DiRT 4\hardwaresettings”.

Open for edit the file “hardware_settings_config.xml”

Search for the string “<motion_platform>” and inside that section you will find a line similar to this one:

<udp enabled="true" extradata="3" ip="127.0.0.1" port="20777" delay="1" />

Ensure the selected values are the same pointed above, specially the “enabled” and “extradata”.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

Start the game with the option:

-telemetry network -ip 127.0.0.1 -port 7701

Specify the IP of the PC running Mover, or 12.0.0.1 for the same PC or 255.255.255.255 to send data to all the network.

You can change the port, but in Mover you have to set the same receive port.

Alternatively,  in the game menu, do:

1. Go to options.

2. Go to telemetry.

3. Specify your settings.

4. Press the button to start telemetry.

Type

MMF - Game should run in same PC you have Mover running.

Setup:

Get the dll file “FlyPT_ETS2_AMTS_MMF.dll” included inside the folder “Sources files” of the Mover download, and copy it inside the installation folder of ETS2/AMTS “...\bin\win_x64\plugins".

Create the plugin folder if needed.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

1. Go to the folder “...Documents\My Games\F1 2016\hardwaresettings”.

2. Open for edit the file “hardware_settings_config.xml”

3. Search for the string:

4. <motion>
   <dbox enabled="true" />
   <udp0 enabled="true" ip="127.0.0.1" port="20777" />
   <udp1 enabled="false" ip="127.0.0.1" port="20777" />
   <udp2 enabled="false" ip="127.0.0.1" port="20777" />
   <udp3 enabled="false" ip="127.0.0.1" port="20777" />
   </motion>

5. Make one of those enabled="true".

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

In the F1 2017 menus, follow the sequence:

1. Game options (by pressing F2).

2. Settings.

3. Telemetry settings.

4. Enable UDP telemetry.

5. Enable broadcast mode for remote access. Sends to all PC's in the network or keep disabled and set the desired IP. Use 127.0.0.1 if you are running on the same PC of Mover.

6. Set port to 20777 or use another one, but should match the one in Mover.

7. Change send rate to maximum (60Hz).

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

In the F1 2018 menus, follow the sequence:

1. Game options (by pressing F2).

2. Settings.

3. Telemetry settings.

4. Enable UDP telemetry.

5. Enable broadcast mode for remote access. Sends to all PC's in the network or keep disabled and set the desired IP. Use 127.0.0.1 if you are running on the same PC of Mover.

6. Set port to 20777 or use another one, but should match the one in Mover.

7. Change send rate to maximum (60Hz).

8. Use 2018 UDP format.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

In the F1 2019 menus, follow the sequence:

1. Game options.

2. Settings.

3. Telemetry settings.

4. Enable UDP telemetry.

5. Enable broadcast mode for remote access. Sends to all PC's in the network or keep disabled and set the desired IP. Use 127.0.0.1 if you are running on the same PC of Mover.

6. Set port to 20777 or use another one, but should match the one in Mover.

7. Change send rate to maximum (60Hz).

8. Use 2019 UDP format.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

In the F1 2020 menus, follow the sequence:

1. Game options.

2. Settings.

3. Telemetry settings.

4. Enable UDP telemetry.

5. Enable broadcast mode for remote access. Sends to all PC's in the network or keep disabled and set the desired IP. Use 127.0.0.1 if you are running on the same PC of Mover.

6. Set port to 20777 or use another one, but should match the one in Mover.

7. Change send rate to maximum (60Hz).

8. Use 2020 UDP format.

Type

MMF - Game should run in same PC you have Mover running.

Setup:

Not required.

Type

SIMCONNECT- Uses FS2020 managed SimConnect.

Setup:

Not required.

Air and ground 

More info here.

Speed effect in drags

Drags are features that cause vibration, like flaps, stall or landing gear.

If speed is zero, there's no vibration, high speeds have more vibration.

Increasing this value, increases vibration for lower speeds.

Type

MMF - Game should run in same PC you have Mover running.

Setup:

You need to install the Microsoft VC++ Redist for 32 bits. Download the file “vc_redist.x86.exe” here:

https://support.microsoft.com/en-us/help/2977003/the-latest-supported-visual-c-downloads

Go to the directory "C:\Program Files (x86)\Steam\steamapps\common\FSX\SDK\Core Utilities Kit\SimConnect SDK\LegacyInterfaces\..." and install all versions of the FSX SDK.

Copy the “FlyPT_FSX_DLL.dll” file included in the “Sources files” folder of the download, to the installation folder of FSX.

Go to the folder "C:\Users\YOUR USERNAME\AppData\Roaming\Microsoft\FSX" and edit the file “dll.xml”. If she doesn't exist, create it with a text editor and copy the text bellow.

If the file exists, you need to add a “<Launch.Addon>” section like shown bellow.

It should end with this aspect (you might have more addons in the file):

The path in bold, should be the one where you have the dll. Like said above, I recommend the installation folder of FSX.

Type

MMF - Game should run in same PC you have Mover running.

Setup:

Not required.

Type

MMF - Game should run in same PC you have Mover running.

Setup:

1. Go to the installation folder of the game.

2. Look for the Plugins folder or if he doesn't exist, look for the Bin32 folder.

3. If both don't exist, create the Plugins folder.

4. If the Bin32 exists, go inside the Bin32 and create the folder Plugins if the folder doesn't exist.

5.  Copy the "FlyPT RFactor MMF.dll" file included in the “Sources files” folder of the download, to the Plugins folder.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

1. Go to the game installation folder "...\IL-2 Sturmovik Battle of Stalingrad\data"

2. Open for edit the file "startup.cfg" and add the following code:

In addr use:

• 127.0.0.1 if IL2 is in the same PC of Mover.

• 255.255.255.255 to send to all PC's on the network.

• The IP of the PC where Mover is running.

Air transition and ground trasition are available in IL2. Go here for more info.

Due to a problem in the data received, we need to force air transition above a certain altitude to the ground, since sometimes it doesn't work with the data received.

That's the reason for the Force air above (m) field where we specify the altitude.

This value depends on planes. It's the CG relative to ground and in big planes it can be high, while in small ones it's low.

Type

MMF - Game should run in same PC you have Mover running.

Setup:

Not required.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

You need to enable UDP in the game, follow this steps:

1. In the game menu, go to settings.

2. Select game.

3. Click in telemetry.

4. Enable UDP output.
    

You can change the UDP port, but she should match the one used in the Mover source.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

To use the LFS source, you need to edit a section of your cfg.txt file.

Go to the LFS installation folder and open the file for edit.

Search for this section and change the values to the following:

If this section is not present in the file, or the file does not exist, you need to make some laps in LFS before the file is completely generated and that section is available.

You can change the UDP ports, but they have to match the ones used by the source in Mover.

The shown ports are the default in Mover.

Warning

Soft transitions work, but not on restarts.
OutSim Opts 1ff is needed on the cfg file to get the latest telemetry info from LFS.
Mover uses that, so you have to set this and use at least version 0.6V of LFS.

Type

TCP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

You should set start parameters to enable telemetry.

If you are using Steam, on the list of games, right click in the game and go to options.

Edit the lauch options to have this: --telemetry --telemetryport=15151

You can change the port, but it should match the port you use in Mover also.

If you don't use a Steam, create a shortcut to the nolimts2 executable and edit the shortcut target to have something like: "nolimits2app.exe" --telemetry --telemetryport=15151

Type

MMF - Game should run in same PC you have Mover running.

Setup:

You need to install the Microsoft VC++ Redist for 64 bits. Download the file “vc_redist.x86.exe” here:

aka.ms/vs/17/release/vc_redist.x64.exe 

Copy the “FlyPT_P3D_DLL.dll” or the  "FlyPT_FSX_DLL.dll" file included in the “Sources files” folder of the download, to "%USERPROFILE%\Documents\Prepar3D "

In that folder add a xml file with the text bellow.

</SimBase.Document>

the name of the file should match the one you selected.

Type

MMF - Game should run in same PC you have Mover running.

Setup:

In the menu do:

1. Options & help.

2. Select visuals.

3. Press hardware in the top right.

4. Enable shared memory.

Type

You can  select two modes, each with is specific source:

MMF - Game should run in same PC you have Mover running.

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup for Project CARS 2 and Automobilista 2:

In the menu do:

1. Go to options.

2. Go to system.

3. In shared memory select Project CARS 2 (if using MMF).

4. In UDP frequency select 1 (if using UDP).

5. In UDP protocol version select Project CARS 2 (if using UDP).

Setup for Project CARS 3:

In the menu do:

1. Go to settings.

2. Go to system.

3. In shared memory select Project CARS 2 (if using MMF).

4. In UDP Mode select 1 (if using UDP).

5. In UDP protocol version select Project CARS 2 (if using UDP).

Type

MMF - Game should run in same PC you have Mover running.

Setup:

Not required.

Type

MMF - Game should run in same PC you have Mover running.

Setup:

Not required.

Type

MMF - Game should run in same PC you have Mover running.

Setup:

Get the file "FlyPT_RFactor2_MMF.dll" included in the folder “Sources files” of the Mover download and copy it to the folder "..\rFactor 2\Bin64\Plugins".

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

This source requires the installation of the NGP6 mod. 

Download and install procedure here: NGP6 .

Next, you need to enable it in the menus:

1. Go to the options.

2. Select Plugins.

3. Select NGP.

4. Enable UDP telemetry.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

Go to the installation folder, and open the file "proxy_udp.ini" inside the wrs folder.

Edit this section to enable UDP output:

Note

Game should be run as administrator.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

Go to the installation folder, and open the file "proxy_udp.ini".

Edit this section to enable UDP output:

Note

Game should be run as administrator.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

Go to the installation folder, and open the file "proxy_udp.ini" inside the wrs folder.

Edit this section to enable UDP output:

Note

Game should be run as administrator.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

Go to the installation folder, and open the file "proxy_udp.ini".

Edit this section to enable UDP output:

Note

Game should be run as administrator.

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

Go to the folder: "...\my Documents\The Crew’"

Create the file "ExtraConfig.xml" with the following text:

Type

UDP - Game can run on the same PC of Mover or another PC in the same network of Mover.

Setup:

To use VTOLVR, you need to use the VTOL VR Mod loader. To get it, got to https://vtolvr-mods.com/ and follow the instructions there.

To install the mod, go to the mods list and search for FlyPT Mover (at https://vtolvr-mods.com/).

The mod, uses port 4124 and broadcasts to IP 127.0.0.1 by default.

To change it, go to the mods main menu in the game and setup the mod to use another IP/port.

Note:

Motion compensation might be a problem in this game. We use the VR controllers to control the plane, so they need to be motion compensated like we do for the headset.